How Do Metal Detectors Work? VLF, PI, and Multi-Frequency
How metal detectors work in plain language: eddy currents, VLF, pulse induction, multi-frequency, ground balance, target ID, and why depth falls off so fast.

Every hobby metal detector, from a $94 starter to a $6,999 gold machine, works on the same principle: induce a current in buried metal and listen for the magnetic echo. What separates the technologies is how they send that field and how they read the echo, and that is what decides which detector suits a park, a salt beach or a goldfield.
This explanation draws mainly on two Minelab knowledge base papers, including “Metal Detector Basics and Theory” by Minelab co-founder Bruce Candy, plus maker spec pages for the frequencies quoted. Where we calculate something ourselves, we say so.
How does a metal detector detect metal?
A metal detector detects metal by electromagnetic induction. A transmit coil carries a changing electric current, which creates a changing magnetic field. That field makes eddy currents flow in any metal object nearby, and the eddy currents create a weak magnetic field of their own, different in shape or timing from the transmitted one. A receive coil picks up that field as a tiny voltage, and the electronics amplify it and decide whether it is metal.
- Electronics drive a changing current through the transmit coil.
- The current creates a magnetic field that reaches into the ground.
- The field induces eddy currents in metal targets.
- The eddy currents produce their own field, altered from the original.
- The receive coil detects that field as a very small voltage.
- The electronics amplify and filter it, then signal with a tone and a target ID.
Candy’s paper notes that deep targets can produce signals millions of times weaker than the transmit signal, which is why amplification and filtering matter so much.
What is the difference between VLF, PI and multi-frequency detectors?
VLF, PI and simultaneous multi-frequency are three ways of sending the field and reading the echo. Each has a natural home ground.
| Technology | How it transmits | Strength | Weakness | Example models (Oct 2026) |
|---|---|---|---|---|
| Single-frequency VLF | One continuous sine wave, about 6 to 61 kHz in current models | Good discrimination, low cost | Struggles on wet salt sand and heavy mineralization | Garrett ACE 400 (10 kHz), Garrett AT Pro (15 kHz) |
| Selectable-frequency VLF | One frequency at a time, chosen by the user | Tune for coins, small targets or the beach | Still one frequency at once | Minelab X-Terra Pro (5, 10, 15 kHz; 8 kHz beach) |
| Simultaneous multi-frequency | Several frequencies at the same moment | Steadier IDs in salt and mineralized ground | Price, deeper menus | Minelab Equinox 900, Nokta Legend, XP Deus II |
| Pulse induction (PI) | Short pulses, then listens after each stops | Ignores most ground mineralization, depth on gold | Weak discrimination, more iron dug | Minelab GPX 6000, Garrett Axiom |
“VLF” stands for very low frequency, the radio band from 3 to 30 kHz where most coin detectors operate; high-frequency gold machines above 30 kHz keep the name because the design is the same. Single-frequency VLF is still the most common design in entry detectors, which is why our best metal detectors list includes both VLF and multi-frequency picks.
How does a detector tell a coin from a nail?
A detector separates a coin from a nail by splitting the echo into two parts. Candy calls them the reactive or X signal, which follows the transmit wave, and the resistive or R signal, which lags behind it. Iron targets produce a positive X signal and non-ferrous targets a negative one, so X tells the detector whether a target is ferrous. A magnet answers only that iron question, which is why magnet fishing pulls up nails but never a gold ring, as our magnet fishing kits guide explains. The balance of X and R tells it the target’s time constant: how long its eddy currents keep flowing.
A time constant rises with a target’s conductivity and size. Candy ranks these from short to long:
| Time constant | Example targets |
|---|---|
| Very short | Small bits of aluminum foil |
| Short | Fine jewelry chains |
| Short to medium | Small old Roman coins |
| Medium | US dime |
| Medium to long | Solid bronze Civil War belt buckle |
| Long | Bronze Age axe head |
| Very long | Large gold ingot, thick copper or aluminum plate |
The target ID number on your screen is the detector’s estimate of where a target sits on that scale. Old pull tabs sit in a narrow, moderately short band, which is why notching them out can also hide small gold rings with similar time constants. Each brand uses its own scale: Garrett runs 0 to 99, current Minelab Equinox and X-Terra models -19 to 99, and the original Nokta Legend 01 to 60. A target ID also cannot tell solid gold from gold plating; the stamp and bench tests in our how to tell if gold is real guide can.
Why does frequency matter?
Frequency changes which targets a detector favors. In Minelab’s words, low frequencies are better at finding bigger, deeper objects, and high frequencies are better at picking up small or thin targets close to the surface. Small gold nuggets and thin jewelry have short time constants and respond better at high frequency.
That is why dedicated gold VLF detectors run high: the Minelab Gold Monster 1000 at 45 kHz, the Garrett Goldmaster 24k at 48 kHz and the Nokta Gold Kruzer at 61 kHz, against roughly 7 to 15 kHz for typical coin machines. Candy adds that natural nuggets give shorter time constants than man-made objects of the same size, because voids and impurities reduce their conductivity. Our gold metal detector guide explains which technology suits which nugget size and ground, and our guide to whether metal detectors can find gold covers what they miss, down to flakes and flour gold.
What does simultaneous multi-frequency add?
Simultaneous multi-frequency lets a detector measure a target’s time constant without leaning on the X signal, which ground mineralization swamps. Short time-constant targets give a larger high-frequency R signal; long time-constant targets give a larger low-frequency R signal. Comparing the R signals at several frequencies therefore gives a time constant that is not contaminated by soil X, according to Candy’s paper.
In practice this means steadier target IDs on wet salt sand, in mineralized soil and in iron-heavy ground, and a detector that is reasonable at both coins and small jewelry at once. Brand names for the idea include Minelab’s Multi-IQ, XP’s Fast Multi Frequency (FMF) and Nokta’s simultaneous multi-frequency. Whether that is worth paying for over a selectable single-frequency machine is the question our X-Terra Pro vs Nokta Legend comparison answers.
How does pulse induction work?
A pulse induction detector sends a burst of current through the coil, switches it off abruptly, and then listens to what decays afterward. Candy compares it to the ignition system of an engine: the magnetic field collapses, and the detector measures the fading fields of eddy currents in metal and of magnetized soil.
Because the transmit field is off while the PI detector listens, there is no X signal at all, only R. Most mineralized soils demagnetize in a predictable way, so the detector can subtract the soil’s decay and keep the metal’s. Candy describes Minelab’s gold PI systems as hundreds of times better than automatic ground-balanced VLF in highly mineralized goldfields. The trade-off is discrimination: without a clean X signal, PI detectors are poor at telling iron from gold, so PI users dig more trash.
What is ground balance, and why does mineralized ground matter?
Ground balance is the detector’s way of cancelling the signal from the soil itself. Many soils contain magnetic iron minerals, and those produce a large X signal with a small R signal. Candy reports soil R to X ratios of roughly 0.5 percent to 5 percent in non-salty goldfield soils, under 0.1 percent for nearly pure magnetite black sand, and as high as about 10 percent in some other soils.
| Ground balance type | How it works | Good for |
|---|---|---|
| Preset (fixed) | Set at the factory for average soil | Parks and yards with mild soil |
| Manual | You adjust how much X is subtracted from R | Experienced users, varying soil |
| Automatic or tracking | The detector adjusts continuously, slowly | Changing ground, beginners |
Geologically young soils, common in North America and Europe after glaciation, are usually only weakly mineralized; old surface soils such as Australia’s goldfields are often heavily mineralized. Mineralization also limits how deep discrimination stays accurate. Sweep the coil level and at a steady speed: Candy notes that bobbing the coil makes the soil signal change quickly enough to pass the filters and cause false readings.
Why do detectors struggle on wet salt sand?
Salt water conducts electricity, so wet salt sand produces an R signal of its own, as Candy notes for salty soils, and a detector can read the beach itself as a large, weak target. Single-frequency VLF detectors respond by chattering or giving jumpy target IDs on wet sand, while dry sand above the high-tide line behaves like ordinary soil.
Simultaneous multi-frequency and pulse induction detectors cope better, and many machines add a beach mode tuned for salt. Black sand rich in magnetite adds a strong X signal on top. Our waterproof metal detector guide compares salt-capable models, and our beach metal detecting guide covers settings for each part of the beach.
How deep can a metal detector detect?
Depth falls off very fast because the field weakens on the way down and the echo weakens again on the way back. Candy’s paper gives the on-axis field of a round mono-loop coil, and the round-trip signal follows from it: proportional to a⁴ / (a² + z²)³, where a is the coil radius and z the target depth. We used that formula to build the table below. It is idealized: a small target directly under a round coil, with no ground noise.
| Target depth | 6 in coil | 11 in coil | 15 in coil |
|---|---|---|---|
| 4 in | 100% (reference) | 100% (reference) | 100% (reference) |
| 6 in | 17% | 34% | 48% |
| 8 in | 4.0% | 12% | 22% |
| 12 in | 0.44% | 1.9% | 4.7% |
| 16 in | 0.08% | 0.42% | 1.2% |
Each column is relative to the same coil at 4 inches. Comparing coils at the same depth, a 15 inch coil returns about 0.6 times the signal of an 11 inch coil at 2 inches but about 2.7 times at 16 inches, while a 6 inch coil returns about 1.6 times more at 2 inches. That is why small coils suit trashy parks and big coils suit open fields. Real depth also depends on target size, orientation, ground and the detector’s noise.
Who invented the metal detector?
Alexander Graham Bell used a four-coil induction balance in July 1881 to try to locate a bullet in President James Garfield. Gerhard Fischer patented an electronic metal detector and began selling Fisher detectors to the public in 1931 through Fisher Research Laboratory; the Fisher brand is still sold today by First Texas. Charles Garrett, co-founder of Garrett Metal Detectors in Texas, pioneered beat frequency oscillator (BFO) machines before VLF designs took over.
Which technology fits the way you hunt?
The technology to buy follows from the ground you hunt. This table connects the physics above to a buying decision.
| You hunt | Physics problem | Technology that solves it |
|---|---|---|
| Parks and yards | Trash and mild soil | Any VLF; small coil for iron and foil |
| Wet salt beaches | Conductive salt sand | Simultaneous multi-frequency or PI, or a beach mode |
| Gold country | Strong mineralization, tiny nuggets | High-frequency VLF or PI |
| Relic fields | Iron masking good targets | Multi-frequency with strong iron handling |
Sources: Minelab, Metal Detector Basics and Theory (Bruce Candy), Minelab, Basic Metal Detector Operation, Minelab, How Detectors Work, Garrett Goldmaster 24k specs, Minelab Gold Monster 1000 specs, Nokta Gold Kruzer, Metal detector history (Wikipedia).
Want to turn this into a shortlist? The Metal Detector Finder applies these same rules, such as salt sand needing multi-frequency or PI, to rank current detectors for your terrain and budget.
Frequently asked questions
Quick answers to what detectorists ask us most
How does a metal detector know what metal it found?
It measures two parts of the returned signal: one that shows whether the target is ferrous (iron) or not, and one that shows how long eddy currents keep flowing in it, its time constant. The detector turns that pair into a target ID number and a tone. It is an estimate, not a chemical test.
What is the difference between VLF and PI metal detectors?
A VLF detector transmits a continuous wave and reads the response while it transmits, which allows good discrimination. A pulse induction (PI) detector sends short pulses and listens after each stops, ignoring most ground mineralization but discriminating poorly. PI suits gold and salt beaches.
How deep can a metal detector detect?
It depends on target size, coil size and ground, but signal falls steeply with depth. With an 11 inch coil, an idealized calculation shows a target at 8 inches returns about one-eighth of the signal it gives at 4 inches, and one at 16 inches about 1/237.
Can metal detectors detect gold?
Yes. Gold rings and coins detect like other non-ferrous metals. Small natural nuggets are harder, because they give weak, short signals, which is why gold detectors run high frequencies (45 to 61 kHz on current VLF gold models) or pulse induction.
Why does my metal detector beep at nothing on the beach?
Wet salt sand conducts electricity, so it produces a signal of its own, and black sand rich in magnetite adds a strong ground signal. Use your detector's beach mode, ground balance on the wet sand, and lower sensitivity until the chatter stops.