Metal Detector Target ID and Tones Explained
What metal detector target ID numbers and tones mean, a conductivity chart for US coins, how VDI scales differ by brand, and why pull tabs read like gold rings.

A target ID number and a tone are the two ways a detector tells you what is buried before you dig. Both come from the same measurement: how a target’s eddy currents behave, which the detector reads as conductivity. Learning to read them is the difference between digging every signal and digging the ones worth your time.
This guide explains what the numbers and tones mean, gives a conductivity chart for common US targets, and shows why the same coin reads differently on each brand. The detection physics behind the numbers is covered in our how metal detectors work guide; here we focus on reading the display.
What does a target ID number actually measure?
A target ID measures conductivity, how freely eddy currents flow in a target and how long they last. The detector maps that onto a scale, usually with iron at the bottom and high-conductor silver at the top. Engineers call the underlying value the time constant, and the screen number is the detector’s translation of it.
Conductivity rises with a metal’s quality and the object’s size and shape. A small, thin, or low-grade metal object gives a short signal and a low number; a large, solid, high-conductor object gives a long signal and a high number. That is why a silver dollar reads near the top and a scrap of aluminum foil reads near the bottom.
What is a target ID conductivity chart for common finds?
Common US targets fall in a predictable order from low to high conductivity. The numbers below are approximate ranges on the Minelab Equinox 0 to 99 scale and will differ on other brands, but the order holds across machines.
| Target | Conductivity | Approx. Equinox ID |
|---|---|---|
| Iron nails, bottle caps | Very low (ferrous) | -9 to 1 |
| Small foil, fine gold chain | Low | 3 to 7 |
| US nickel, small gold rings | Low to mid | 12 to 13 |
| Pull tabs, mid-size gold | Mid | 14 to 19 |
| Zinc penny, screw caps | Mid to high | 19 to 22 |
| US dime, copper penny | High | 24 to 30 |
| US quarter | High | 29 to 33 |
| Silver quarter, large cent | Very high | 33 to 38 |
| Silver dollar, copper plate | Highest | 38 to 40 |
Treat these as a map, not a guarantee. Depth, soil mineralization and a target lying on edge all drag numbers down and make them jump, which is covered below.
How do tones relate to the numbers?
Tones are the audio version of the target ID, grouped into pitch ranges. A low tone means low conductivity (iron and ferrous trash), a mid tone means the nickel-to-gold range, and a high tone means high conductors like copper and silver. Experienced detectorists hunt by tone first and glance at the number to confirm.
Detectors offer different tone counts for a reason:
- Two tones split targets into low (iron) and high (everything else), simple and fast for silver hunting.
- Multi-tone (five, fifty, or full-range) gives each conductivity band its own pitch, so you judge a target by ear.
- Tone breaks let you set where one tone changes to the next, matching the pitch split to the trash you want to ignore.
- Ferrous or iron audio adds a distinct grunt for iron so you can hear it under good targets.
Full-range or tone-ID systems, like those on the XP Deus II and the current Minelab models, pitch the tone in proportion to the ID, so a rising pitch as you sweep often signals a good target rather than iron.
Why do brand scales differ, and does it matter?
Every maker uses its own scale, so the same coin shows a different number on each brand. It matters because you cannot copy another hunter’s “dig this number” advice across machines; you learn your own detector’s numbers for local targets.
| Brand or model | Scale | US quarter reads about |
|---|---|---|
| Garrett (ACE, AT, Apex) | 0 to 99 | 80 to 85 |
| Minelab (Equinox, X-Terra, Manticore) | -9 to 99 | 29 to 33 |
| Nokta Legend | 0 to 60 | 38 to 42 |
| Fisher and Teknetics | 0 to 99 | 80s |
The quickest way to learn your scale is an air test: wave known coins past the coil and note the numbers, then bury a few at depth in your yard and note how the readings drop. Our comparisons of the Equinox 800 vs 900 and the X-Terra Pro vs Nokta Legend cover how these scales behave on each machine.
Why do pull tabs and gold rings read the same?
Because they share a conductivity range, no target ID can separate a small gold ring from an aluminum pull tab or a bit of can slaw. Both are mid-conductive, so both land in that 12 to 19 band on the Equinox scale, and the detector genuinely cannot tell them apart.
This is the central problem of jewelry hunting. If you notch out the pull-tab range to avoid trash, you also notch out small gold. Gold hunters accept the trade and dig the mid-range, which is why our guide on whether detectors can find gold stresses that finding gold means digging signals a coin hunter would skip. There is no setting that keeps the gold and drops the tabs.
How does depth change the target ID?
Depth drags the target ID down and makes it less stable, because the signal weakens fast as a target sinks. A quarter that reads a confident high number at 3 inches may read lower and jump around at 9 inches, and a deep coin can masquerade as mid-range trash.
This is why experienced hunters weight a signal’s repeatability over its exact number on deep targets. If a faint signal gives roughly the same tone and a believable number from two or three directions, it is worth digging even when the ID is not textbook. A number that swings wildly as you change angle usually means iron, a target lying on edge, or two objects close together. Mineralized soil amplifies the effect, pulling numbers down further, which is one more reason to ground balance properly before trusting the screen.
How do you use notch and discrimination without losing good targets?
Use discrimination sparingly, because every range you silence can hide a good target with the same conductivity. Discrimination mutes targets below a set point, and notch mutes a specific band such as the pull-tab range.
Both help you ignore iron in a clean park, but they cut both ways. Notching the pull-tab band also silences small gold rings that share that conductivity, and discriminating out low numbers mutes small, deep or on-edge coins that read low. The safer habit for most sites is to run little discrimination and judge targets by tone and repeatability, digging the signals that sound and read consistently from several angles. Save heavy discrimination for sites so full of iron that digging it all is impractical.
Who should ignore the target ID?
Deep-target and relic hunters often trust tone and dig habits over the number. A target ID is reliable only for shallow, clean, flat targets; at depth, on edge, or beside iron, the number becomes unstable and misleading, so leaning on it costs you good finds.
Beginners also benefit from digging more than the IDs suggest at first, to learn how numbers map to real objects in their soil. Mineralized ground, salt sand and masking iron all distort readings, so the hunters who rely least on the screen are often the most experienced. To match a detector’s ID system and tone options to the way you hunt, run the Metal Detector Finder.
Sources: Minelab, Target ID and Discrimination (knowledge base), Minelab Equinox 900 instruction manual, XP Deus II program and tone guide, Nokta Legend user manual, Garrett ACE Apex target ID (Garrett).
Frequently asked questions
Quick answers to what detectorists ask us most
What do the numbers on a metal detector mean?
They are the target ID, the detector's estimate of a target's conductivity. Low numbers mean iron and small foil, middle numbers mean nickels, gold and pull tabs, and high numbers mean copper and silver coins. The scale and exact numbers differ by brand.
What target ID is gold on a metal detector?
There is no single gold number. Gold spans a wide range: thin chains and small rings read low, near foil and nickel, while heavy rings read higher. That overlap with pull tabs is why gold hunting means digging mid-range signals rather than trusting the ID.
What do the different tones mean?
Tone follows conductivity: a low tone for iron and ferrous trash, a mid tone for nickels and gold, and a high tone for copper and silver. Multi-tone modes give each range its own pitch so you can judge a target before you look at the screen.
Why does my detector show different numbers for the same coin?
Depth, angle, nearby iron, mineralized soil and ground balance all shift the reading. A coin on edge or beside a nail reads low and jumpy. Bob the coil at a steady height and check the ID from several directions before deciding.
Can I trust the target ID to avoid digging trash?
Only partly. IDs are reliable for shallow, clean targets and unreliable for deep, angled or masked ones. Notching out trash ranges also hides good targets with the same conductivity, such as small gold rings sitting in the pull-tab range.